AEM V3 Water/Methanol Injector Nozzle Kit, 30-3315
Machined Billet Injectors and Nozzles
AEM includes one precision-machined billet injector in its Nozzle & Jet kit. It features an integral check valve to prevent unintended fluid flow. Three atomizing pintles are included for matching water/methanol flow to an engine’s horsepower output.
AEM Nozzle Kit Features:
- Precision-machined billet-aluminum injector with integral check valve
- 1/4" T-Fitting
- Three interchangeable atomizing pintles to cover a wide variety of HP levels (250cc/min, 500 cc/min & 1,000cc/min)
- 1 foot of Injection Tubing
Legal in California only for racing vehicles which may never be used upon a highway.
Important Safety Notice Regarding Methanol
AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component.
All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems.
Methanol is a toxic and highly flammable chemical. 100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe. The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol.
WARNING!
Improper installation and/or adjustment of this product can result in major engine/vehicle damage.
Note: AEM holds no responsibility for any engine damage or personal injury that results from the misuse of this product, including but not limited to injury or death caused by the mishandling of methanol.
Note: FOR OPTIMUM RESULTS, ALL WATER/METHANOL INJECTION SYSTEMS AND GAUGES SHOULD BE RUN WITH AN AEM INLINE FILTER (AEM PART #30-3003)
AEM includes one precision-machined billet injector in its Nozzle & Jet kit. It features an integral check valve to prevent unintended fluid flow. Three atomizing pintles are included for matching water/methanol flow to an engine’s horsepower output.
AEM Nozzle Kit Features:
- Precision-machined billet-aluminum injector with integral check valve
- 1/4" T-Fitting
- Three interchangeable atomizing pintles to cover a wide variety of HP levels (250cc/min, 500 cc/min & 1,000cc/min)
- 1 foot of Injection Tubing
Legal in California only for racing vehicles which may never be used upon a highway.
Important Safety Notice Regarding Methanol
AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component.
All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems.
Methanol is a toxic and highly flammable chemical. 100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe. The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol.
WARNING!
Improper installation and/or adjustment of this product can result in major engine/vehicle damage.
Note: AEM holds no responsibility for any engine damage or personal injury that results from the misuse of this product, including but not limited to injury or death caused by the mishandling of methanol.
Note: FOR OPTIMUM RESULTS, ALL WATER/METHANOL INJECTION SYSTEMS AND GAUGES SHOULD BE RUN WITH AN AEM INLINE FILTER (AEM PART #30-3003)
More from this collection
